4 Prong Trolling Motor Plug Wiring Diagram

Last year my dealer already replaced my factory TM wiring with two 6 gauge wires running from my 2 TM batteries to the bow receptacle. The 2 batteries already have a short jumper cable between them to make 24 volts at the receptacle. A 60 amp circuit breaker is in place at the battery. I was provided the following Marinco 4 Prong male plug to attach to the trolling motor wires: Marinco BP as in following link http: But I don’t need that since my jumper is back at the batteries, and the directions do not adequately explain what to do in that situation. So how do I attach my 2 TM wires correctly to the plug? I assume if I connect black to – and red to 24v, I will avoid any effects of the internal 12 to 24 jumper in the plug. It depends how your dealer wired the 2 6 wires to the receptacle, Marinco’s directions are pretty sketchy for a 2-wire 24V scheme. Here’s an old posting on the subject https: Do you want to sell that boat today, or not? So I bought a new to me boat this fall, and I just recently took the Maxxum motor off and bought a new Terrova to put on. I forgot to really look at the old plug before I sold the motor but I think I need this one: Should there be a concern with water intrusion in this plug or is it best to just leave it plugged in. My last boat I had the Marinco twist style with a rubber plug to insert when not in use Guest, If I were you, I would remove the Marinco socket that is installed in your boat and replace it with a Battery Tender socket. Then, install the matching Battery Tender plug on the trolling motor cable. Thus, the wire drapes down the front of the bulkhead and does not stick out where it may be hit with a foot or leg when fishing in the boat. Also, the Battery tender has a nice screw in and screw out plug which makes for a fail safe connection and ease of connecting and disconnecting. The problem with the Marinco socket, as is the case with many of the trolling motor plugs and sockets on the market, is that they are not set up to handle 6 gauge wire. As a result, it makes a perfect installation, on this plug a difficult job. But, the Battery tender plugs and sockets have nice appropriate sized connectors and openings for the use of 6 gauge wire. Then, I would do the same thing with the – battery wire and connect the two lighter wires to the two remaining connectors on the Marinco 4 connector socket. Then, I would repeat the process for the Trolling motor plug. Finally, repeat for the – trolling motor plug wire. Attach the two lighter wires to the two remaining connectors on the Marinco plug that match the connecting points to the Marinco socket that you wired up in your boat. But a big hassle to do this and you need the right very heavy duty crimper to insure that you have a good job of crimping the butt splices for the heavier 6 gauge wire to the two lighter jumper wires for each side of the plug and socket connections. Last edited by REW; at Originally Posted by walleye patrol2. Originally Posted by Wall-i-Lama. Another very nice thing about the Battery tender plug and socket is that the trolling motor wire comes out of the plug at right angles. Originally Posted by ckraning. I have the Battery Tender installed and love it. I have not had any issues with it, unlike other plugs on the boat–yes, a little more pricey, but worth it. All times are GMT The time now is Page 1 of 2. Remove Advertisements Sponsored Links. Hot Runr Guy Wallhanger. Send a private message to Hot Runr Guy. Find all posts by Hot Runr Guy. Plug question So I bought a new to me boat this fall, and I just recently took the Maxxum motor off and bought a new Terrova to put on. Send a private message to walleye patrol2. Find all posts by walleye patrol2. Be safe Last edited by REW; at Send a private message to REW. Find all posts by REW. Originally Posted by walleye patrol2 So I bought a new to me boat this fall, and I just recently took the Maxxum motor off and bought a new Terrova to put on. Send a private message to Wall-i-Lama. Find all posts by Wall-i-Lama. Originally Posted by Wall-i-Lama Another very nice thing about the Battery tender plug and socket is that the trolling motor wire comes out of the plug at right angles. Send a private message to ckraning. Find all posts by ckraning. Send a private message to Walleye Find all posts by Walleye

I am working with a four prong outlet and it has four wires running to the Anyway now that I know I have juice up front I plug the motor in and. i just bought a 24v trolling motor (upgrade from a 12) i looked at the powering diagram and stripe)that go to the plug in for the trolling motor, the plug in is a 4 prong, when i bought Here’s a diagram for 3 a wire setup.

female end of plug has 4 wires conected to it (red, orange, black, and black with blue.

For Marinco ConnectPro Receptacle and Plug (12VCP). WARNING: To determine the size fuse required, consult your trolling motor specification manual.

Follow the wiring diagrams exactly. 4.

Make certain there is no wire insulation inside the terminals, and there are no stray wire strands outside the terminals. The rear left/port side has a circuit breaker with 4 wires coming out.

Announcement

It had a switch at the bow next to the troll motor plug for 12/off/ I have found a number of wiring diagrams depicting that arrangement. If you have a 24v only system you will have to 4 prong ranger plug and no selector switch on the.

This Trolling Motor Plug, cat. no.

BgB’s Weekly Wire: Hubbell Twist Lock Plug

trolling motor to a Marinco 4-wire receptacle, cat. no.

the two batteries are wired to the receptacle as shown in Fig. 1.The 4-wire trolling/charging system eliminates the need for a charge/run switch.

Install the receptacle on the boat, mount the black plug on the trolling motor and the red plug on the leads of the battery charger. The Marine Raider 4-Prong Female Trolling Motor Receptacle features a universal design and is made of high-impact plastic.

receptacle 12/24v bass oem pack 50/master compare prev 1 next.

Mar 05,  · Re: 24 volt Motor guide hookup w/4 prong I might be wrong here, but I think the 4 prong male end that is wired to the trolling motor has a jumper built in it. Take a look at the male prong to see if you can see the metal jumper between two prongs.

Yeh, I know, 4 holes to put two wires into.

Find great deals on eBay for 4 prong trolling motor plug. Shop with confidence.

A close-up look of Marinco trolling motor receptacle (Part 1 of 2)

Skip to main content. eBay: 5 product ratings – Boater Sport Male Trolling Motor 4 Plug prong Replace Marinco BP MD.

$ Buy It Now +$ shipping. 80 Sold 80 Sold.

5 new & refurbished from $3 Wire Diagram Marinco | Wiring Library4 wire trolling motor plug | eBay